Scope 1.1 This specification covers grades of seamless, welded, and heavily cold worked welded austenitic and ferritic/austenitic stainless steel sanitary tubing intended for use in the dairy and food industry and having special surface finishes. Pharmaceutical quality may be requested, as a...
Online InquiryScope
1.1 This specification covers grades of seamless, welded, and heavily cold worked welded austenitic and ferritic/austenitic stainless steel sanitary tubing intended for use in the
dairy and food industry and having special surface finishes. Pharmaceutical quality may be requested, as a supplementary requirement.
1.2 This specification covers tubes in sizes up to and including 12 in. (304.8 mm) in outside diameter.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 Optional supplementary requirements are provided, and when one or more of these are desired, each shall be so stated in the order
2. Referenced Documents
2.1 ASTM Standards:2
A 262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A 480/A 480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
A 923 Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels
A 967 Specification for Chemical Passivation Treatments for Stainless Steel Parts
A 1016/A 1016M Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
E 527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
2.2 ASME Standard:
B46.1 Surface Texture (Surface Roughness, Waviness, and Lay)3
2.3 ASME Boiler and Pressure Vessel Code: Section VIII Pressure Vessels3
2.4 Other Standard: SAE J1086 Practice for Numbering Metals and Alloys(UNS)4
3. Terminology
3.1 Definition:
3.1.1 roughness average, Ra, n—arithmetic average surface roughness normally reported in microinches or microns; a
measurement of surface roughness usually performed by moving a stylus in a straight line along the surface, although other methods may be used.
|
TABLE 1 Chemical Requirements |
||||||||||||
|
Element |
Grade |
TP 304 |
TP 304L |
… |
TP 316 |
TP 316L |
… |
… |
… |
… |
… |
2003 |
|
UNS |
S30400 |
S30403 |
S31254 |
S31600 |
S31603 |
N08926 |
N08367 |
S31803 |
S32205 |
S32750 |
S32003 |
|
|
Composition, % |
||||||||||||
|
Carbon, max |
0.080 |
0.035B |
0.020 |
0.080 |
0.035B |
0.020 |
0.030 |
0.030 |
0.030 |
0.030 |
0.030 max |
|
|
Manganese,max |
2.00 |
2.00 |
1.00 |
2.00 |
2.00 |
2.00 |
2.00 |
2.00 |
2.00 |
1.20 |
2.00 max |
|
|
Phosphorus,max |
0.045 |
0.045 |
0.03 |
0.045 |
0.045 |
0.03 |
0.04 |
0.03 |
0.03 |
0.035 |
0.03 |
|
|
Sulfur, max |
0.03 |
0.03 |
0.01 |
0.03 |
0.03 |
0.01 |
0.03 |
0.02 |
0.02 |
0.02 |
0.020 max |
|
|
Silicon, max |
1.00 |
1.00 |
0.80 |
1.00 |
1.00 |
0.50 |
1.00 |
1.00 |
1.00 |
0.80 |
1.00 max |
|
|
Nickel |
8.0–11.0 |
8.0–12.0 |
17.5–18.5 |
10.0–14.0 |
10.0–14.0 |
24.0–26.0 |
23.5–25.5 |
4.5–6.5 |
4.5–6.5 |
6.0–8.0 |
3.0–4.0 |
|
|
Chromium |
18.0–20.0 |
18.0–20.0 |
19.5–20.5 |
16.0–18.0 |
16.0–18.0 |
19.0–21.0 |
20.0–22.0 |
21.0–23.0 |
22.0–23.0 |
24.0–26.0 |
19.5–22.5 |
|
|
Molybdenum |
… |
… |
6.0–6.5 |
2.00–3.00 |
2.00–3.00 |
6.0–7.0 |
6.0–7.0 |
2.5–3.5 |
3.0–3.5 |
3.0–5.0 |
1.5–2.0 |
|
|
Nitrogen C |
… |
… |
0.18–0.22 |
… |
… |
0.15–0.25 |
0.18–0.25 |
0.08–0.20 |
0.14–0.20 |
0.24–0.32 |
0.14–0.20 |
|
|
Copper |
… |
… |
0.50–1.00 |
… |
… |
0.50–1.5 |
0.75 max |
… |
… |
0.50 max |
… |
|
|
A New designation established in accordance with Practice E 527 and SAE J 1086. |
||||||||||||
|
B For small diameter or thin walls or both, where many drawing passes are required, a carbon maximum of 0.040 % is necessary in grades TP304L and TP316L. Small outside diameter tubes are defined as those less than 0.500 in. (12.7 mm) in outside diameter and light wall tubes as those less than 0.049 in. (1.24 mm) in average wall thickness (0.044 in. (1.12 mm) in minimum wall thickness). |
||||||||||||
|
C The method of analysis for nitrogen shall be a matter of agreement between the purchaser and manufacturer. |
||||||||||||
|
TABLE 2 Permissible Variations in Dimensions |
||||
|
Size,Outside,Diameter,in. (mm) |
Permissible Variations in Outside Diameter, in. (mm) |
Permissible Variations in Cut Length, in. (mm)A |
||
|
Over |
Under |
Over |
Under |
|
|
1.000 (25.4) and under |
0.005 (0.13 |
0.005 (0.13 |
1⁄8 (3.2) |
0 |
|
Over 1 (25.4) to 2 (50.8) |
0.008 (0.20) |
0.008 (0.20) |
1⁄8 (3.2) |
0 |
|
Over 2 (50.8) to 3 (76.2) |
0.010 (0.25) |
0.010 (0.25) |
1⁄8 (3.2) |
0 |
|
Over 3 (76.2) to 4 (101.6) |
0.015 (0.38) |
0.015 (0.38) |
1⁄8 (3.2) |
0 |
|
Over 4 (101.6) to 5 1⁄2 (139.7), excl |
0.015 (0.38) |
0.015 (0.38) |
3⁄16 (4.8) |
0 |
|
5 1⁄2 (139.7) to 8 (203.2), excl |
0.030 (0.76) |
0.030 (0.76) |
3⁄16 (4.8) |
0 |
|
8 (203.2) to 12 (304.8) |
0.050 (1.27) |
0.050 (1.27) |
3⁄16 (4.8) |
0 |
A The cut tolerances do not apply to Pharmaceutical Tubing in S2 (see paragraph S2.7).
TABLE S2.1 Tensile and Hardness Requirements
|
Grade |
UNS |
Tensile |
Yield |
Elongation |
Rockwell |
|
TP304 |
S30400 |
75 (515) |
30 (205) |
35 |
B90 |
|
TP304L |
S30403 |
70 (485) |
25 (170) |
35 |
B90 |
|
TP316 |
S31600 |
75 (515) |
30 (205) |
35 |
B90 |
|
TP316L |
S31603 |
70 (485) |
25 (170) |
35 |
B90 |
|
S31803 |
90 (620) |
65 (450) |
25 |
C30.5 |
|
|
2205 |
S32205 |
95 (655) |
70 (485) |
25 |
C30.5 |
|
2507 |
S32750 |
116 (800) |
80 (550) |
15 |
C32 |
|
2003 |
S32003 |
90 (620) |
65 (450) |
25 |
C32 |
|
ASTM A249/A269/A270, JIS G3447/G3463, CNS 6668/7383 |
||||||||
|
Standard/Item |
Outside Diameter |
Thickness |
Length |
|||||
|
ASTM A249 |
|
O.D .<< p=""> |
25mm |
+0.10mm |
, -0.11mm |
±10% |
O.D. < 50.8mm +3.0mm |
|
|
25mm≦ |
O.D.≦ |
40mm |
± 0.15mm |
|
-0mm |
|||
|
40mm << p=""> |
O.D. << p=""> |
50mm |
±0.20mm |
|
O.D.≧ 50.8mm +5.0mm |
|||
|
50mm≦ |
O.D. << p=""> |
65mm |
±0.25mm |
|
-0mm |
|||
|
65mm≦ |
O.D. << p=""> |
75mm |
±0.30mm |
|
|
|||
|
75mm≦ |
O.D.≦ |
100mm |
±0.38mm |
|
|
|||
|
100mm << p=""> |
O.D.≦ |
200mm |
+0.38mm |
, -0.64mm |
|
|||
|
200mm << p=""> |
O.D.≦ |
225mm |
+0.38mm |
, -1.14mm |
|
|||
|
ASTM A269 |
|
O.D. << p=""> |
38.1mm |
±0.13mm |
|
O.D. < 12.7mm ±15% |
O.D. < 38.1mm +3.2mm |
|
|
38.1mm≦ |
O.D. << p=""> |
88.9mm |
±0.25mm |
|
O.D.≧ 12.7mm ±10% |
-0mm |
||
|
88.9mm≦ |
O.D. << p=""> |
139.7mm |
±0.38mm |
|
|
O.D.≧ 38.1mm +4.8mm |
||
|
139.7mm≦ |
O.D. << p=""> |
203.2mm |
±0.76mm |
|
|
-0mm |
||
|
ASTM A270 |
|
O.D.≦ |
25mm |
±0.13mm |
|
±12.5% |
O.D.≦ 100mm +3mm |
|
|
25mm << p=""> |
O.D.≦ |
50mm |
±0.20mm |
|
-0mm |
|||
|
50mm << p=""> |
O.D.≦ |
75mm |
±0.25mm |
|
O.D. > 100mm +5mm |
|||
|
75mm << p=""> |
O.D. << p=""> |
140mm |
±0.38mm |
|
-0mm |
|||
|
CNS 6668 |
|
O.D.≦ |
25.4mm |
± 0.15mm |
|
±10% |
+10mm |
|
|
JIS G3447 |
25.4mm << p=""> |
O.D.≦ |
31.8mm |
± 0.16mm |
|
-0mm |
||
|
31.8mm << p=""> |
O.D.≦ |
38.1mm |
± 0.19mm |
|
|
|||
|
38.1mm << p=""> |
O.D.≦ |
76.3mm |
± 0.25mm |
|
|
|||
|
76.3mm << p=""> |
O.D.≦ |
89.1mm |
± 0.30mm |
, -0.40mm |
|
|||
|
89.1mm << p=""> |
O.D.≦ |
101.6mm |
± 0.35mm |
, -0.40mm |
|
|||
|
101.6mm << p=""> |
O.D.≦ |
114.3mm |
± 0.40mm |
, -0.60mm |
|
|||
|
114.3mm << p=""> |
O.D.≦ |
139.8mm |
± 0.40mm |
, -0.80mm |
|
|||
|
139.8mm << p=""> |
O.D.≦ |
165.2mm |
± 0.40mm |
, -1.20mm |
|
|||
|
JIS G3463 |
|
O.D. << p=""> |
60mm |
±0.25mm |
|
O.D. < 40mm |
t < 2mm +0.4mm |
O.D.≦ 50mm + 7mm |
|
60mm≦ |
O.D. << p=""> |
80mm |
±0.30mm |
|
-0.0mm |
- 0mm |
||
|
80mm≦ |
O.D. << p=""> |
100mm |
±0.40mm |
|
t≧ 2mm +20% |
O.D. > 50mm +10mm |
||
|
100mm≦ |
O.D. << p=""> |
120mm |
+0.40mm |
, -0.60mm |
-0mm |
-0mm |
||
|
120mm≦ |
O.D. << p=""> |
160mm |
+0.40mm |
, -0.80mm |
O.D.≧ 40mm |
22% |
|
|
|
160mm≦ |
O.D. << p=""> |
200mm |
+0.40mm |
, -1.20mm |
-0mm |
|
||
|
200mm≦ |
O.D. |
|
+0.40mm |
, -1.60mm |
|
|
||
SUNRISE is well-known as one of the leading astm a270 seamless austenitic and ferritic and austenitic stainless steel sanitary tubing manufacturers and suppliers in China for its quality products and excellent service. We warmly welcome you to buy the quality and durable steel products from our factory.
